Thursday, August 18, 2011

Repair Your Broken Vertical Blind Vanes

If you own vertical blinds, you've probably needed to repair or replace a vane that broke out at the top where it clips to the head rail.

Replacement slats are often expensive and hard to find.

Matching the color, size, and pattern to the rest of the vanes on an existing blind is difficult.

Vertical vane savers will solve your problem. Watch this YouTube video to see how it works.


Monday, November 1, 2010

How to Center a 2-Way Draw Curtain Rod

via RepairWindowBlinds.com by Dave on 1/8/10

Once you restring your center draw curtain rod it should look something like this photo when seen from the back side. In the photo, the carrier on the left (the one with the knots) is what I call the primary or master carrier.

Center Draw Traverse Rod

Center Draw Traverse Rod Seen From the Back - Click to Enlarge

You will need to put the rod back up on the wall and re-hang the drapery or curtain on the rod before you proceed.

Positioning the Master Carrier

Pull on the draw cord to close the drape, the primary carrier will traverse until the drapery or curtain panel on that side is fully extended. If the rod was properly installed to match the width of the curtain, the carrier will be in the center of the rod.

Positioning the Secondary Carrier

To set the position of the secondary carrier, hold the pull cord tightly in one hand so that the primary carrier doesn't move and then slide the secondary carrier towards the center of the rod until it butts against the primary carrier.

The secondary carrier has a small slot where the cord is exposed (see photo below)

Center Draw Traverse Rod - Secondary Carrier

Center Draw Traverse Rod - Secondary Carrier - Click to Enlarge


Pull the Loop

Using a small screwdriver, pull the exposed cord out to form a loop as seen below.

Curtain Rod Center Adjustment - Pull Out the Loop - Click to Enlarge

Curtain Rod Center Adjustment - Pull Out the Loop - Click to Enlarge


Anchor the Loop

Now place the loop over the anchor point on the carrier.

The anchor point for the rod shown is a plastic tab located just below the cord slot. On some other brands of traverse rod the anchor point(s) will be small tabs located on either side of the cord slot - you'll know them when you see them. You only need to anchor the cord to one of those tabs. Which one you choose is up to you. I don't think it matters.

Traverse Rod Center Adjustment - Anchor the Loop - Click to Enlarge

Traverse Rod Center Adjustment - Anchor the Loop - Click to Enlarge


Snug it Up!

Finally, you pull on the draw cord until the cord loop is snug to the anchor point and you're done!

Now when you operate the pull cord, both sides should open and close in unison and they should come together neatly in the center every time.

Curtain Rod Center Adjustment - Snug it Up - Click to Enlarge

Curtain Rod Center Adjustment - Snug it Up - Click to Enlarge


Some Final Thoughts

As you can see, this whole process is pretty simple.

It is important to hold the pull cord so that the primary carrier doesn't move away from center while you are anchoring the cord to the secondary carrier. Of course, if something does go haywire, you can always disconnect the anchor point and start over.

With a little trial and error you'll have things up and running in no time.

As always, please leave a comment if you have any further questions. Have fun!

Blinds.com

Sunday, October 31, 2010

7 Tips for Accurate Measurements

If you want a professional installation, you must start by measuring like a professional. Dimensions can vary by several inches from window to window even though they appear to be the same size. Always measure every window!

via Install-Window-Blinds.com by blindsInstaller on 3/16/09

  1. Measure Every Window

If you want a professional installation, you must start by measuring like a professional. Dimensions can vary by several inches from window to window even though they appear to be the same size. Always measure every window!

  • Use the Right Measuring Tool
  • A tape with a wide blade (1" or more) is easy to work with because it is rigid enough to span the window without bending or kinking and it can stand up on it's own for an easy vertical measurement. If you have trouble reading the divisions on a tape you may want to consider one with a fractional blade or scale. A fractional scale reads directly in fractions of an inch making it easy to interpret the division marks. A laser measure is even easier to work with and very accurate.

  • Choose Your Window Treatment Before You Measure
  • Each type of window covering has it's own unique set of measuring requirements. None of it is rocket science, but you can't know what to do or what to look out for if you haven't decided which type of blind or shade you want to buy. Select the type of product that you want before you measure.

  • Check Each Dimension in (at least) 3 Places
  • Window opening dimensions often vary from side to side and top to bottom within the same window. As the installer, it is your job to identify the largest and smallest dimension in each direction. Depending upon your choice of blind or shade you will need this information to make an informed decision about which dimensions you should use when ordering.

  • Be Consistent When You Write Down Your Measurements - (part1)
  • It is the standard in the industry to record window covering dimensions as width followed by height. If you are such a rebel that you just can't conform to this standard, be sure to label your dimensions so you'll remember which is which when it comes time to place your order (if the retailer doesn't insist upon using the standard notation, you may want to consider using a different retailer).

  • Be Consistent When You Write Down Your Measurements - (part 2)
  • Use a measurement worksheet and label each window. When measuring a room with more than one window, go around the room in a clockwise direction (or whatever - the main thing is to be consistent). Label each window as you go around the room. For example, in the dining room you might label them as "din1", "din2", etc. Keep your worksheet where you can find it so you can use it as a reference to lay out the job for installation.

  • Do a Reality Check
  • Be sure to scan the completed worksheet for dimensions that seem out of place. For instance, if all of the windows in the breakfast nook measure out at approximately 36" x 48" except for one oddball at 36" x 45", you would probably want to check your work again.